This page described describes the installation process of Dbvisit StandbyMP on Linux and Windows platforms.
You much must review & complete all Installation Requirements prior to starting installation: Installation Requirements
1. Linux
| Note |
|---|
Never use root user for Installation of Dbvisit StandbyMP on Linux |
| Note |
|---|
This installation procedure is not valid for Oracle RAC and SEHA environments. Refer to <<TBD>> instead |
Step 1: Create a "Dbvisit Base" Directory
This step needs to be done on primary, standby and dbvcontrol server (if different from standby server).
This step is the only exception where we will need to use root privileges. The default location is /usr/dbvisit. You can specify any location you need as long as has enough free space (see Installation Requirements ). Following commands can be used to create installation directory:
| Code Block |
|---|
sudo mkdir /usr/dbvisit
sudo chown oracle:oinstall /usr/dbvisit |
The ownership of the directory needs to be changed to the user who will install and run Dbvisit (Oracle/SQLServer/Postgres Database software owner).
Step 2: Download and Extract Latest Software
This step needs to be done on primary, standby and dbvcontrol server (if different from standby server).
The latest available version can be downloaded from the Dbvisit web site https://www.dbvisit.com
Once the software is downloaded, you can upload / copy it to a temporary location on your server, do not use Dbvisit Base location. Make sure the ownership of the file is set to the same user who owne Dbvisit Base:
| Code Block |
|---|
mkdir /tmp/dbvisit cd /tmp/dbvisit # now upload files chown oracle:oinstall /tmp/dbvisit |
...
1. Linux
| Note |
|---|
Never use root user for Installation of Dbvisit StandbyMP/standby-v12.1.tar.gz
tar -xzf standby-v12.1.tar.gz |
Verify you can now see two installer files:
| Code Block |
|---|
-rwxr-xr-x. 1 oracle oinstall 188106709 Jan 28 09:54 install-agent-v12.1
-rwxr-xr-x. 1 oracle oinstall 64448219 Jan 28 09:52 install-control-v12.1 |
Step 3: Install Dbvisit StandbyMP dbvagentmanager
This step needs to be done on primary and standby server only
You can start the installation by running in install-agent file:
| Code Block |
|---|
cd /tmp/dbvisit
./install-agent-v12.1 |
You will need to respond to following prompts during installation:
Prompt | Example Value | Comment |
|---|---|---|
Please carefully read the end-user license agreement at https://dbvisit.com/eula. Do you agree to the terms of this agreement? | Yes | Installation will proceed only with response “Yes” |
Which directory should the software be installed into? | /usr/dbvisit | Dbvisit Base directory you prepared earlier |
Agent File Transfer Port: (7890) | There’s usually no need to change the port, press enter to accept suggested value | |
Fully Qualified Domain Name for this host: [? for help] (czlin0231) | czlin0231 | hostname (including domain name or not) of your primary server. Hostname must be resolvable into valid IPv4 address and such interface needs to be present on the host |
Fully Qualified Domain Name for the Control Center: | czlin0232 | hostname (including domain name or not) where you will install your dbvcontrol. Hostname must be resolvable into valid IPv4 address. It is not required for controlcenter to be installed / running at this point. |
Agent Communications Port:(5533) | There’s usually no need to change the port, press enter to accept suggested value | |
Passphrase: | Admin123 | passphrase used for encrypting communication between dbvagentmanagers and dbvcontrol. Must match on all hosts. There is no complexity requirement. |
Example complete output of installation:
| Expand | ||
|---|---|---|
| ||
|