Log onto the VM through the VirtualBox console which will be shown when the VM has started. 

The username is root and the password is oracle

1. When logged onto the desktop, right click and click on "Open Terminal" to bring up the terminal.

Image Removed

2. In the terminal edit  /etc/sysconfig/network

[root@localhost ~]# vi /etc/sysconfig/network

and change to:

NETWORKING=yes
HOSTNAME=source

3. Edit /etc/hosts and add the following two hosts entries

# Do not remove the following line, or various programs
# that require network functionality will fail.
127.0.0.1		localhost
::1				localhost
10.0.2.4       source-int source dbv01
10.0.2.5       target-int target dbv02

4. Right click on the Network Manager icon on the top right hand corner, and click on "Edit Connections..."

Image Removed

5. Click on Auto eth1 and click on "Edit..."

Image Removed

6. 

Change the settings to the following (do NOT change the HWADDR or UUID)

DEVICE=eth1
HWADDR=08:00:27:d8:37:29
TYPE=Ethernet
ONBOOT=yes
BOOTPROTO=none
IPADDR=10.0.2.4
NETMASK=255.255.255.0
GATEWAY=10.0.2.1
NETWORK=10.0.2.0
UUID=c4a351d7-380f-4dd9-a7ad-a92c30cf01c0
NM_CONTROLLED=no
IPV6INIT=no

5. Ensure  HWADDR in ifcfg-eth1 above is set to the same value as ATTR{address} in the following file.

cat /etc/udev/rules.d/70-persistent-net.rules

# This file was automatically generated by the /lib/udev/write_net_rules
# program, run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.
# PCI device 0x8086:0x100e (e1000)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="08:00:27:d8:37:29", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"

5. Restart the network interface

# /etc/init.d/network restart
Shutting down interface eth0:                              [  OK  ]
Shutting down loopback interface:                          [  OK  ]
Bringing up loopback interface:                            [  OK  ]
Bringing up interface eth0:                                [  OK  ]

6. View the network interface

# ifconfig
eth0      Link encap:Ethernet  HWaddr 08:00:27:18:B5:AF  
          inet addr:10.0.2.4  Bcast:10.0.2.255  Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fe18:b5af/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:241 errors:0 dropped:0 overruns:0 frame:0
          TX packets:330 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:21781 (21.2 KiB)  TX bytes:47325 (46.2 KiB)
          Interrupt:10 Base address:0xd020 
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:3670 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3670 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:4306552 (4.1 MiB)  TX bytes:4306552 (4.1 MiB)

There is only one network interfaces:

• eth1 which is a fixed IP address. This is used to connect between the source and target servers and also to the Internet. This IP is 10.0.2.4.

7. scp (secure copy) does not work because there is display output in ~oracle/.bashrc and ~oracle/.bash_profile. To fix this:

a. Edit .bashrc in the home directory of oracle

cd ~oracle

vi .bashrc

Put a # in front of the following lines:

#cat ~/Desktop/README.txt


#/sbin/ifconfig | grep "inet addr"

b. Edit  .bash_profile in the home directory of oracle

cd ~oracle

vi .bash_profile

Put a # in front of the following lines:

...

When the machine_setup script has been edited to accept the EULA and the memory parameter adjusted, execute the script. The script takes about 5-10 minutes to execute depending on your host PC. When the script finishes, both the source and target machines should be running and available to log into.

What the script does

Imports the source and target machines into VirtualBox, sets up the Host-only adapter in the network settings, sets up the shared folder drive, sets the snapshot folder and snapshot the machine as a fresh clean starting position that can be returned to if required. The machine_setup scrip will then start both source and target machines.

On Windows

In the %REP_HOME%\Rep Attack 11g XE directory, execute the machine_setup.bat script by double clicking on it. A command prompt window will open and the RepAttack source machine will be configured and started, followed by the target machine.

For example:

Image Added

On Mac OS X and Linux machines:

Open a Terminal window and change directory to the REP_HOME directory.

Execute the machine_setup.bash script.

bash-3.2$ ./machine_setup.bash