Log onto the second VM (dbv02) through the VirtualBox console which will be shown when the VM has started.
The username is root and the password is oracle
1. When logged onto the desktop, right click and click on "Open Terminal" to bring up the terminal.
2. In the terminal edit /etc/sysconfig/network
[root@localhost ~]# vi /etc/sysconfig/network
and change to:
NETWORKING=yes NETWORKING_IPV6=no HOSTNAME=target
3. Set the network address for eth1
cd /etc/sysconfig/network-scripts
vi ifcfg-eth1
Change the settings to the following (do NOT change the HWADDR)
# Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] DEVICE=eth1 BOOTPROTO=none ONBOOT=yes HWADDR=08:00:27:19:c2:f8 IPADDR=10.1.1.11 NETMASK=255.255.255.0
4. Restart the network interface
[root@source network-scripts]# /etc/init.d/network restart
Shutting down interface eth0: [ OK ]
Shutting down interface eth1: [ OK ]
Shutting down loopback interface: [ OK ]
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0... done.
[ OK ]
Bringing up interface eth1:
5. View the network interface
[root@source network-scripts]# ifconfig
eth0 Link encap:Ethernet HWaddr 08:00:27:BF:36:00
inet addr:10.0.0.21 Bcast:10.0.0.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:febf:3600/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:118125 errors:0 dropped:0 overruns:0 frame:0
TX packets:682 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:31908626 (30.4 MiB) TX bytes:76611 (74.8 KiB)
Interrupt:10 Base address:0xd020
eth1 Link encap:Ethernet HWaddr 08:00:27:19:C2:F8
inet addr:10.1.1.11 Bcast:10.1.1.255 Mask:255.255.255.0
inet6 addr: fe80::a00:27ff:fe19:c2f8/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:120 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:23113 (22.5 KiB)
Interrupt:9 Base address:0xd060
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:35521 errors:0 dropped:0 overruns:0 frame:0
TX packets:35521 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:7421628 (7.0 MiB) TX bytes:7421628 (7.0 MiB)
There are 2 network interfaces:
a) eth0 which is a DHCP address so that a connection can be made from the host computer (your laptop). In this case the IP is 10.0.0.21
b) eth1 which is a fixed IP address. This is used to connect between the source and target servers. This IP is 10.1.1.11
6. Restart the VM (dbv02)
shutdown -r now
7. Start the first VM (dbv01) again by clicking on Start
0 Comments